CrimeStopper RS-901 User Manual

RS900/RS901 SERIES V RS999 FM FLASHBACK™ NEW FEATURES! Timed Crank mode, Diesel Delay time, & Pos. or Neg. glow plug input. REMOTE ENGINE S

AFTERMARKET MOTOR/DOOR LOCK WIRINGREVERSE POLARITY DOOR LOCK WIRINGGREENGREENFUSEDFUSEDREDRED+12V+12VBLUEBLUE++8685868586858685878787873087A3087A3087A

HOW to REDUCE “SMART TACHLESS” CRANKING TIME: In the event “Smart Tachless” mode slightly over-cranks the starter motor, the settings can be changed.

TACH FINDER MODE: This CoolStart system includes a Tach Finder mode to assist in locating a valid or viable tach source for your installation. Follow

This new feature provides an easy method of starting the vehicle without locating an exact tach wire. It uses a timed cranking output combined with t

This new feature provides a solution for diesel vehicle without having to connect to the Glow Plug-“Wait to Start Circuit”. This may be due to a varie

Option # Option Description Option Values Button #1 LOCK Button #2 UNLOCK 1. Tach Learning Tach Reference (Page 10) Learn Tach2. Autolock wit

PROGRAMMABLE OPTIONS CHART CONTINUED 17 Diesel Glow Plug Delay Button #1 = 10 Sec. Button #2 = Monitor Glow plug Button #3 = 20 Sec. Button #4 = 3

PROGRAMMABLE OPTIONS 6. Passive Starter Disable: Note: Yellow/Black Negative Output must be programmed as an “Anti-Grind” for this feature. See opti

PROGRAMMABLE OPTIONS 16. Pre-Set Starter Cranking Time: (Requires Option #15 in “Timed Crank” Setting) This option controls the starter output cr

900 V TRANSMITTER / 999FM TRANSCEIVER CODE LEARNING Transmitter/Transceiver Code Learning: (Excludes RS901) Note: Remote Transmitters/Transceivers

TABLE OF CONTENTS Pre-Installation Considerations……….………...……...………………………………………………………………..………2 Cautions & Warnings…….……………...….……..…..…………………………

2-VEHICLE OPERATION Both the RS-900 V and RS-999FM systems can be used for 2 car operation. A single RS900V remote can control two independent vehic

TROUBLESHOOTING: “BEFORE YOU CALL” SECTION UNIT WILL NOT ATTEMPT A START (KEYLESS ENTRY FUNCTIONS NORMALLY): The unit is in Valet mode. Turn IGN O

JUMPER PIN DIAGRAMS Jumper pins are used to change/configure the operation of the on board multi-function output PINK/WHITE wire, the Parking Light

GLOW PLUGPINK WIRE:Jumper Select forPostive or NegativeType "Wait" Circuits ANTENNA DIAGRAM

WINDSHIELDANTENNALOCATIONSWhite PlugBlack PlugRS-900 VRS-999FM

TRANSMISSIONPROGRAMPARKINGLIGHTSSWITCHECURS900/901ANTENNA/RECEIVER PLUGLEDCOIL(-) UNLOCK OUTPUT+12 V FOR RELAYS(-) LOCK OUTPUTENGINEECUGREENRED/WHITET

PLAN OUT YOUR INSTALLATION and determine most suitable locations for all components to be placed. These components include: the module itself, valet/

PIN 3: YELLOW/BLACK: (-) IGNITION OUTPUT -or- ANTI-GRIND/STARTER DISABLE OUTPUT This negative output wire is programmable and can function two differe

TOIGN 2MOTORACCSTARTCUTBROWNYELLOW/BLACK8685MAKE CERTAIN TO CONNECT "BROWN" START OUTPUT WIRE TOMOTOR SIDE OF ANTI-GRIND/START DISABLE RELA

wire is used, the RS900/901/999FM system will wait until light turns off before attempting a remote start. Note: This input is jumper selectable for

(2) RED: +12V POWER INPUT WIRES (30A Fused): Connect to both of these leads to +12V Constant Power. We recommend the BATTERY POSTIVE TERMINAL. PINK:

FUSEREDPINK/WHITE30AFUSERED30A+-BROWNPINKFUELENGINEBATTERYPUMPECUGRAY+STARTER-COILIGNORACCH/V/ACDiagram not to scale,for illustration purposesonly. Yo

PIN 1: GREEN: (-) Negative pulse for LOCK PIN 2: RED: +12V When using external relays (TERM 86) PIN 3: BLUE: (-) Negative pulse for UNLOCK COMMON D